ISO 2846-1 PDF

Partie 1: Impression lithographique offset sur feuilles et à bobines. STANDARD. ISO. Third edition. Reference number. ISO (E). ISO is an international standard used to determine color and transparency conformance of four- color lithographic printing inks. determining if “High Tack Bengal Process Series” inks conformed to ISO ISO – was performed using an IGT Printability Tester. The four inks were.

Author: Misho Faurr
Country: Chad
Language: English (Spanish)
Genre: Sex
Published (Last): 16 November 2005
Pages: 470
PDF File Size: 13.56 Mb
ePub File Size: 9.44 Mb
ISBN: 762-8-45594-297-6
Downloads: 1415
Price: Free* [*Free Regsitration Required]
Uploader: Tojakinos

The colour values determined in the standard are a further approach to standardise offset printing. Transparency As process printing inks have to show sufficient transparency for the functioning of multi colour printing, corresponding values have been stipulated in ISOwhich may not be undercut. It was very difficult to define the colorimetric nominal values which are to be the future chromaticity coordinates of the standardized printing inks, as values had to be found that were acceptable to all experts from the various economic areas.

Colour values It was very difficult to define the colorimetric nominal values which are to be the future chromaticity coordinates of the standardized printing inks, as values had to be found that were acceptable to all experts from the various economic areas.

It is based on and conforms to our current knowledge. The term for this new series was European 28846-1 scale or sometimes shortened to European scale.

In practice, however, this means that when launching colour management, the already used ink series in the print shop should serve as reference considering the commonly used full tone densities in the print shop.

ISO Epple Druckfarben AG

Examination of transparency For the evaluation of the transparency, several printing samples with graduating ink film thicknesses are to be printed on black substrate. As process printing inks have to show sufficient transparency for the functioning of multi colour printing, corresponding values have been stipulated in ISOwhich may not be undercut.

  5218A IC PDF

There are some colour systems on the market which work with up to seven colours in order to display the widest isp colour space. However as actual application is affected by many factors over which we have no control, we are not liable for printing failures.

That means that the difference between printed and blank black increases. In general, izo number of primary colours is optional; for economic reasons, however, not isoo many primary 28846-1 should be used. The four-colour system has established itself in the main printing procedures, however. Input values and average ISO value for magenta. In complete accordance with the European colour scale, the international standard ISO was published in The revision for offset printing is complete with the present standard ISO Europe For Europe, the average values of more than 60 current process inks from different producers were generated.

Print products should be produced and also reproduced, again and again, all over the world, with the same results. The colours cyan, magenta and yellow also correspond to this standard. Information on standard ISO For multi-colour printing the inks are mixed by printing primary colours over or next to each other in solid and screen areas.

For Europe, the average values of more than 60 current process inks from different producers were generated. In case a printing ink is not totally transparent, the light that touches the print sample during observation or colour measurement is increasingly scattered according to higher ink film thickness.

According to our measurements, the most common ink series, especially ours, are at least very close to the nominal value and mostly within the given tolerances. The inclination is then 0. Compliance with the standard is given if the measured values do not exceed the stipulated value of transparency. The usage of defined process printing inks with fixed properties in terms of colour is one of the most important preconditions to achieve reproducible print results.

  MAGAZYN CLAUDIA PDF

Measurement geometry Standard illuminant: This also applies as the standard for sheet-fed offset.

ISO 2846 Conformance Tested Ink & Suppliers

For multi-colour printing the inks are mixed by printing primary colours over or next to each other in solid and screen areas. This colour definition was stipulated in standard DIN 16 In order to achieve better fastness properties, for example alkali or light fastness, a group of experts from the CEPE European Council of producers and importers of paints, printing inks and artists colours recommended the standardization of a new ink series, in At complete transparency sometimes to be found with cyana horizontal line shows.

The reciprocal value of the inclination of oso line of best fit by the measuring points, describes the extent of transparency.

For the evaluation of the transparency, several printing samples with graduating ink film thicknesses are to be printed on black substrate. These series are produced by us with utmost care and are delivered with the lowest colour metric fluctuations.

ISO 2846-1

This technical instruction iwo is designed for your information and reference. Input values and average ISO value for cyan transparency. Colour values for black were also included in the new standard. If the colour distance between printed and blank black is put down as function of the ink film thickness, a line arises whose inclination is low at a high transparency of the printing ieo and higher if the transparency is lower.

In process inks were standardized for the first time in Germany with DIN 16 for letterpress and DIN 16 for offset printing. Input values and average ISO value for yellow.